Module
Showing 1–36 of 159 results
- Electronic Parts, Module
37 in 1 Sensor Kit With Bag
out of stock- For beginners who are interested in Arduino
- A complete set of Arduino’s most common and useful electronic components
- Infrared sensor receiving module
- Laser sensor module
- Temperature and humidity sensor module
- Infrared sensor module
- 5v relay module
- Obstacle avoidance sensor module.
SKU: EAP-000774 - Detection & Sensor Module, Electrical, Electrical & Mechanical, Electronic Parts, Module, Sensors, Sensors
37 in Sensor Kit
Stock outDetection & Sensor Module, Electrical, Electrical & Mechanical, Electronic Parts, Module, Sensors, Sensors37 in Sensor Kit
out of stock- For beginners who are interested in Arduino
- A complete set of Arduino’s most common and useful electronic components
- Infrared sensor receiving module
- Laser sensor module
- Temperature and humidity sensor module
- Infrared sensor module
- 5v relay module
- Obstacle avoidance sensor module.
SKU: EAP-000388 - Electronic Parts, Module, Wireless Module
4 Channel Remote Kit
31 in stock- No. of the channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- Transmitter Radiated power: 10mW at 12V.
- Transmission distance (m): 3 to 5.
SKU: EAP-000418 - Electronic Parts, Module, Motor Driver Module
A3967 Stepper Motor Driver Module
5 in stock- Power supply: 7V to 30V.
- The higher the voltage, the higher the torque at high speeds.
- Adjustable current control from 150mA/phase to 750mA/phase.
- Logic voltage: 5V or 3.3V.
- A3967 microstepping driver.
SKU: EAP-000424 - Electronic Parts, Module, Motor Driver Module
A4988 Stepper Motor Driver Module
4 in stock- Five different micro-steps
- Full step
- Half step
- Quarter step
- Eight steps
- Sixteen steps
- Direction control
- Overcurrent and over-temperature protection
- Adjustable current limit
- Short to ground
- Shorted load protection
- Automatically selects the correct current delay
SKU: EAP-000423 - Five different micro-steps
- Electronic Parts, Module, Power Supply Module
AMS1117-3.3V Voltage Regulator Module
5 in stockThis voltage regulator module is based on the AMS1117 3.3V regulator. It is capable of regulating a wide range of input voltage (4.0 to 12V) down to a fixed 3.3V output at up to 1A (Vin = 4.5V). Standard 0.1″ header pins provide a means of connecting to its input and output terminals. These header pins have also been conveniently placed so that the module can be inserted face down into standard.
SKU: EAP-000911 - Electronic Parts, Module, Power Supply Module
AMS1117-3.3V Voltage Regulator Module
11 in stock- 3.3V Output
- 5V Input. Can use higher input voltages, but see our notes below about derating the current at higher voltages
- 800mA maximum rated current. 500mA recommended max
- Power LED
- Short circuit and thermal protection built-in
- Small footprint
SKU: EAP-000880 - Electronic Parts, Module, Power Supply Module
Breadboard Power Supply Module(3.3V, 5V)
10 in stock- Breadboard power supply module, compatible with 5V, 3.3V.
- Apply to MB102 breadboard
- Input voltage: 6.5-12 V (DC) or USB power supply
- Output voltage: 3.3V/5V can switch over
- Maximum output current: <700 ma
- Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V
- On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use.
SKU: EAP-000643 - Electronic Parts, Module, Motor Driver Module
CNC Shield V3
4 in stock- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
SKU: EAP-000701 - Electronic Parts, Module, Power Supply Module
DC 12V to 3.3V,5V and 12V Power Supply module
1 in stock- Output power on/off switch
- Two-row multiple pin outputs, easy to use and connect
- Red LED illuminates when input DC power is supplied and output is turned ON.
- Small and Handy Module.
- Dual-side plate design.
- Easy to use.
SKU: EAP-000515 - Electronic Parts, Module
DC Voltmeter (0~30V, Red, 0.36″)
9 in stock- Measuring range: 0-30 V
- Maximum Input Voltage: 30V
- Display Color: Red
- Dimension: 23 x 15 x 10mm (L x W x H)
- Display Type: 3 Digit 0.36″ LED display
- Cable Length: 195mm
- Display Type: 3Digit 0.36” LED Display
- 0.1V for above 10V, 0.01V for below 10V
SKU: EAP-001088 - Electronic Parts, Module, Power Supply Module
DC-DC Step-up Adjustable Power Supply Module (150W, 6A)
In StockElectronic Parts, Module, Power Supply ModuleDC-DC Step-up Adjustable Power Supply Module (150W, 6A)
5 in stock- Input voltage :10-32V
- Output voltage: 12-35V (adjustable)
- Output Current: 10A (MAX)
- Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A)
- The non-isolated step-up power conversion module
- Onboard LED illuminates when the voltage is applied to the module
SKU: EAP-000758 - Electronic Parts, Module, Motor Driver Module
DRV8833 2 Channel Motor Driver Module
5 in stock- Dual-H-bridge motor driver:
- Operating voltage: 2.7 V to 10.8 V
- Output current: 1.2 A continuous (2 A peak) per motor.
- Motor outputs can be paralleled to deliver 2.4 A continuous (4 A peak) to a single motor.
- 3V- and 5V Logic Voltage compatible
- Under-voltage lockout and protection against over-current and over-temperature.
- Reverse-voltage protection circuit.
- Current limiting can be enabled by adding sense resistors.
SKU: EAP-000877 - Electronic Parts, Module
ESP8266 Serial Port Baseboard Lua WIFI Development Board
3 in stock- Lead-out all the IO ports of the ESP-12E development board
- Lead out the pins of 5V and 3.3V power supply
- Convenient to connect with peripheral modules
- Onboard 5V / 1A DC-DC step-down converter circuit
- Onboard power indicator
- With DC power jack 6-24V.
SKU: EAP-000759 - Electronic Parts, Module, Power Supply Module
HI-LINK Power Supply (12V,1.6A)
2 in stock- Meet UL, CE requirements,
- Ultra-thin, ultra-small
- All voltage input (AC: 100 ~ 240V)
- Low ripple and low noise
- Output overload and short circuit protection
- High efficiency, high power density
- The product is designed to meet the requirements of the EMC and Safety Test
- Low power consumption, environmental protection, no-load loss <0.1W
SKU: EAP-000363 - Electronic Parts, Module, Power Supply Module
HI-LINK Power Supply (5V,2A)
out of stock- Meet UL, CE requirements,
- Ultra-thin, ultra-small
- All voltage input (AC: 100 ~ 240V)
- Low ripple and low noise
- Output overload and short circuit protection
- High efficiency, high power density
- The product is designed to meet the requirements of the EMC and Safety Test
- Low power consumption, environmental protection, no-load loss <0.1W
SKU: EAP-000362 - Electronic Parts, Module, Power Supply Module
HIECUBE Dual Power Supply (5V/12V, 36W)
2 in stock- Input voltage: 85-265VAC / 100-370VDC
- Output voltage, Vout1: 5V DC
- Output voltage, Vout2: 12V DC
- Output current, Vout1: 0.5A
- Output current, Vout2: 3.0A
- Power Max: 5W
- Output voltage accuracy: ± 1%
- Size (L x W x H): 48 * 36 * 23mm.
SKU: EAP-000361 - Battery Charging Module, Electronic Parts, Module, Power Supply Module
IP5328P Power Bank Module with 5V 9V 12V Step up Fast Quick Charging (5V 3.1A, QC2.0 QC3.0, Dual USB Output, Micro and Type-C Input)
In StockBattery Charging Module, Electronic Parts, Module, Power Supply ModuleIP5328P Power Bank Module with 5V 9V 12V Step up Fast Quick Charging (5V 3.1A, QC2.0 QC3.0, Dual USB Output, Micro and Type-C Input)
8 in stock- Input: Type C or Micro USB fast charging capable
- Output: 5V-3.1A, 7V-2.4A, 9V-2.0A, 12V-1.5A | Output Interface: Dual USB PD output and Type C PD
- Chipset: IP5326P; 4 onboard SMD LED to display battery charge level
- Output Interface: USBA + USBA + TYPE-C support fast charge output (see protocol specification fast charge)
- Overcharge protection | Overdischarge protection | Overcurrent protection
- Size : 64*32*6mm (L*W*H)
SKU: EAP-001025 - Electronic Parts, Module
IR Infrared Obstacle Avoidance Sensor Module
2 in stock- Main Chip: LM393
- Operating Voltage (VDC): 3.6 ~ 5
- Average Current Consumption (mA): 0.06
- Detection Angle: 35 °
- Distance Measuring Range (CM): 2 ~ 30
- Dimensions (mm) LxWxH: 48 x 14 x 8
- Weight (gm): 5
- Shipment Weight: 0.01 kg
- Shipment Dimensions: 5 × 4 × 1 cm
SKU: EAP-000658 - Detection & Sensor Module, Electronic Parts, Module
KY-033 Linetracking sensor
10 in stock- Working voltage: DC 3.3V-5V
- Working current: ≥ 20mA
- Operating temperature: -10℃~+50℃
- Detection distance: 2-40cm
- IO Interface:3-wire interfaces
- Output signal: TTL level (low level there is an obstacle, no obstacle high)
- Adjustment: adjust multi-turn resistance
SKU: EAP-000910 - Electronic Parts, Module, Motor Driver Module
L293D Mini Motor Driver Module
2 in stock- New L293D motor shield, the input voltage DC4.5-25V
- 600mA output current capability per channel
- 1.2A peak output current(non-repetitive) per channel
- Enable facility
- Overtemperature protection
- Logical “0” input voltage up to 1.5V(High noise immunity)
SKU: EAP-000757 - Electronic Parts, Module, Power Supply Module
LM2596S DC-DC Step-down Adjustable Power Supply Module
In StockElectronic Parts, Module, Power Supply ModuleLM2596S DC-DC Step-down Adjustable Power Supply Module
8 in stock- Model:LM2596S
- Input voltage: 4-32V
- Output Voltage: 1.5-30V (adjustable)
- Output current: rated current 2A, maximum 3A (heat sink required)
- Conversion efficiency: Up to 92% (the higher the voltage, the higher the efficiency)
- Switching Frequency: 150KHz
- Rectifier: Non-Synchronous Rectification
- Module Properties: Non-isolated step-down module (buck)
- Short circuit protection: current limiting
- Operating temperature: Industrial grade (-40 ℃ to +85 ℃) (output power 10W or less)
- Full load temperature rise: 40 ℃
- Load regulation: ± 0.5%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Output ripple:
- Input 12V Output 5V 3A 60mV (MAX)
- Input 24V Output 12V 3A 120mV (MAX)
- Input way: IN+, IN-
- Output way: OUT+, OUT-
SKU: EAP-000508