No products in the cart.
Detection & Sensor Module, Electronic Parts, Module, Trending Items
MAX30102 Heart Rate and Pulse Oximeter Module
Availability:
Out of stock
The MAX30102 Heart Rate and Pulse Oximeter Module is a high-performance biometric sensor designed to measure heart rate (HR) and blood oxygen saturation (SpO₂). It integrates red and infrared LEDs, a photodetector, optical components, and low-noise analog signal processing into a compact module. With an I2C interface, it can be easily connected to Arduino, ESP32, STM32, Raspberry Pi, and other microcontrollers for health monitoring and wearable applications.
14,800 Ks
Out of stock
Features
- Measures Heart Rate (HR) and Blood Oxygen Saturation (SpO₂)
- Built-in MAX30102 optical biometric sensor
- Red & Infrared LEDs with integrated photodetector
- Digital I2C communication interface
- Low power consumption for battery-powered devices
- High sensitivity and accurate signal acquisition
- Compatible with Arduino, ESP32, STM32, Raspberry Pi, and other MCU platforms
- Compact size for wearable and portable projects
- Ideal for health monitoring, fitness trackers, and biomedical applications
- Sensor IC: MAX30102
- Measured Parameters: Heart Rate (HR), Blood Oxygen (SpO₂)
- Operating Voltage: 3.3V – 5V DC
- Communication Interface: I2C
- I2C Address: 0x57
- Operating Current: Ultra Low Power
- LED Type: Integrated Red & Infrared LEDs
- Output: Digital
- Pin Interface: VIN, GND, SCL, SDA, INT
- Compatible Boards: Arduino, ESP32, ESP8266, STM32, Raspberry Pi
- Applications: Health Monitoring, Wearable Devices, Fitness Trackers, Biomedical Projects, IoT Systems
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
- DIY Items, Electronic Parts, Module, Relay Module
2 Channel Relay Module (5V,10A)
8 in stock- Switching mains loads
- Home automation
- Battery backup
- High current load switching
- Supply voltage – 3.75V to 6V
- Trigger current – 5mA
- Current when relay is active – ~70mA (single), ~140mA (both)
- Relay maximum contact voltage – 250VAC, 30VDC
- Relay maximum current – 10A
SKU: EAP-000012 - DIY Items, Electronic Parts, Module, Relay Module
4 Channel Relay Module (5V,10A)
3 in stock- Useful for appliance control
- DC or AC signal, control, you can control the 220V AC load
- There is a normally open and one normally close contact
- The module is compliant with international safety standards, control and load areas isolation trenches
SKU: EAP-000011 - Detection & Sensor Module, Electronic Parts, Module
Raindrop Detection Sensor Module
423 in stock- The LM393, use of the wide voltage comparator
- Provide both digital and analog output
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- The sensor uses the high-quality FR – 04 double material, the large area of 5.5*4.0 CM
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15mA
- With potentiometer sensitivity adjustment
- The output format: digital switch output (0 and 1) and analog AO voltage output;
- Has a fixed bolt hole, convenient installation
SKU: EAP-000001 - DIY Items, Electronic Parts, Module, Relay Module
1 Channel Relay Module (5V,10A)
18 in stock- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches.
SKU: EAP-000013
There are no reviews yet.