This is FS1000A 433mHz Tx RF Radio Module. This RF module comprises an RF Transmitter and an RF Receiver. The transmitter/receiver (Tx/Rx) pair operates at a frequency of 433 MHz. An RF transmitter receives serial data and transmits it wirelessly through RF through its antenna connected at pin4. The transmission occurs at the rate of 1Kbps – 10Kbps. The transmitted data is received by an RF receiver operating at the same frequency as that of the transmitter.
Electronic Parts, Module
RF Transmitter Module (433MHz)
Availability:
In stock
- Transmission distance: 50-100m
- Working voltage : 3.5-12V (DC)
- Modulation: AM
- Transfer rate: 4kB/s
- Transmit power: 10mW
- Emission frequency: 433MHz
- External antenna: 25cm ordinary multi-core or single core line
- Pinout from left to right: DATA; VCC; GND
- Dimensions (L x W): 19 x 19mm
5,800 Ks
In stock
Based on 0 reviews
0.0 overall
0
0
0
0
0
Only logged in customers who have purchased this product may leave a review.
Related products
- DIY Items, Electronic Parts, Module, Relay Module
1 Channel Relay Module (5V,10A)
18 in stock0 out of 5(0)- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator lamp
- Control indicator lamp
- Indicator for Relay output status
- Can Be controlled various appliances & other Equipment With Large current.
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
- The module is compliant with international safety standards, control and load areas isolation trenches.
SKU: EAP-000013 - Electronic Parts, LCD Display Module, Module
20×4 LCD Display Module + I2C Expander Module
0 out of 5(0)- 2004 204 20X4 Character LCD Display Module Blue Backlight
- Blue & Green backlight
- Fully assembled and tested Serial LCD 20×4 Module
- Display Format: 20 Characters x 4 lines
- Supply voltage: 5V
- The module can be easily interfaced with a MCU
- The module is a low-power consumption character LCD Module with a built-in controller
SKU: n/a30,000 Ks This product has multiple variants. The options may be chosen on the product page - Electronic Parts, Module, OLED Display Module
TM1637 Clock Display Module
46 in stock0 out of 5(0)- Ease to use.
- Ease of multiplexing.
- Can use as a 4 digit display unit.
- Can use as a clock display.
- DIY clock project.
- 4 digit display unit.
- Electrical/Electronic projects.
- The counter project using 7 segment display.
- 4 M2 screws positioning holes for easy installation
SKU: EAP-000007 - Development Board, Electronic Parts, Raspberry Pi
Raspberry Pi Pico RP2040 Programming Development Board
Stock outDevelopment Board, Electronic Parts, Raspberry PiRaspberry Pi Pico RP2040 Programming Development Board
Out of stock0 out of 5(0)- RP2040 microcontroller chip designed by Raspberry Pi
- 264KB of SRAM, and 2MB of onboard Flash memory
- The castellated module allows soldering directly to carrier boards
- Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz
- Drag-and-drop programming using mass storage over USB
- 26 × multi-function GPIO pins
- 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Accurate clock and timer on-chip
- Onboard temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
SKU: EAP-000607







There are no reviews yet.