No products in the cart.
Electronic Parts, Module
Ultrasonic Mist Maker + USB Driver Module for Humidifier (5V, Ø16mm, Micro USB)
Availability:
In stock
Parameter
- Rated voltage: DC 5V
- Rated current: 300mA
- Power: 1.5-2W
- Resonant frequency: 108-110KHz
- Material: 1.2mm FR-4
- Size：35×18×13mm (LxWxH)
5,000 Ks
In stock
Spray Pattern
1.continuous spraying mode: press the switch once, the LED light is always on, continuous spraying mode, always spraying, after 4 hours of spraying, automatic shutdown protection.
2. intermittent spray mode: press the switch twice, the LED light flashes, intermittent spray mode, spray 10 seconds, stop spraying 5 seconds, and so on cycle, spray 12 hours later, automatic shutdown protection.
3.shutdown: press the switch three times: shutdown
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
- Electronic Parts, Module, LCD Display Module
20×4 LCD Display Module + I2C Expander Module
in stock- 2004 204 20X4 Character LCD Display Module Blue Backlight
- Blue & Green backlight
- Fully assembled and tested Serial LCD 20×4 Module
- Display Format: 20 Characters x 4 lines
- Supply voltage: 5V
- The module can be easily interfaced with a MCU
- The module is a low-power consumption character LCD Module with a built-in controller
SKU: n/a - Electronic Parts, Module, Detection & Sensor Module
HTU21D Temperature and Humidity Sensor Module
In StockElectronic Parts, Module, Detection & Sensor ModuleHTU21D Temperature and Humidity Sensor Module
7 in stock- Uses the I2C interface
- Typical humidity accuracy of ±2%
- Typical temperature accuracy of ±0.3C
- Operates from 0 to 100% humidity but this sensor isn’t recommended for harsh environments where it could come in contact with water (such as rain)
- 3.3V sensor – use inline logic level converters or 10k resistors to limit 5V signals
- Only one HTU21D sensor can reside on the I2C bus at a time
SKU: EAP-000002 - Electronic Parts, Module, Detection & Sensor Module
Raindrop Detection Sensor Module
12 in stock- The LM393, use of the wide voltage comparator
- Provide both digital and analog output
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- The sensor uses the high-quality FR – 04 double material, the large area of 5.5*4.0 CM
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15mA
- With potentiometer sensitivity adjustment
- The output format: digital switch output (0 and 1) and analog AO voltage output;
- Has a fixed bolt hole, convenient installation
SKU: EAP-000001 - Electronic Parts, Development Board, Raspberry Pi
Raspberry Pi Pico RP2040 Programming Development Board
In StockElectronic Parts, Development Board, Raspberry PiRaspberry Pi Pico RP2040 Programming Development Board
3 in stock- RP2040 microcontroller chip designed by Raspberry Pi
- 264KB of SRAM, and 2MB of onboard Flash memory
- The castellated module allows soldering directly to carrier boards
- Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz
- Drag-and-drop programming using mass storage over USB
- 26 × multi-function GPIO pins
- 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
- USB 1.1 with device and host support
- Low-power sleep and dormant modes
- Accurate clock and timer on-chip
- Onboard temperature sensor
- Accelerated floating-point libraries on-chip
- 8 × Programmable I/O (PIO) state machines for custom peripheral support
SKU: EAP-000607
There are no reviews yet.